Intersoft Community - Crosslight - Error when creating a new Crosslight 2 project

Error when creating a new Crosslight 2 project

yudi — Wed, 21 May 2014 22:39:54 GMT

@Nicholas Turner

I sent a message to the registered email account. Please kindly check your inbox and let me hear your response.

Error when creating a new Crosslight 2 project

handy@intersoftpt.com — Mon, 19 May 2014 21:20:52 GMT

Hello,

I tried to run the attachment on 64bit and it works fine. Did you get any error? Please let us know in details.

Regards,
Handy

Error when creating a new Crosslight 2 project

nick5454 — Mon, 19 May 2014 14:17:40 GMT

Can you add the 64 bit version please. I believe that is the 32 bit. I'm running win 7 ultimate 64 bit VM

Error when creating a new Crosslight 2 project

technical@intersoftpt.com — Mon, 19 May 2014 12:37:41 GMT

We've improved the License Manager to address the missing product issue when upgrading to a new release. Could you please try the License Manager and see if it works fine in your end?

Note that one of the registry entries should contain Crosslight 2, i.e., whether it's in the 64 bit registry or in 32 bit. If you cannot find it in both registry entries, you might have deleted incorrect entry previously.

Hope this helps!

Error when creating a new Crosslight 2 project

nick5454 — Mon, 19 May 2014 12:13:38 GMT

I deleted the entry and rebooted my machine and still no 2.0 crosslight. See attached screen shot

Error when creating a new Crosslight 2 project

technical@intersoftpt.com — Sat, 17 May 2014 03:21:53 GMT

Dear Nicholas, You will need to delete the Intersoft Solutions registry item, then re-run License Manager. This issue usually occur when the registry was somehow not cleaned up during previous uninstallation. We have logged this issue and will improve the overall experience in the upcoming release. Please let us know if this works well in your end. Thanks! Hope this helps.

Error when creating a new Crosslight 2 project

nick5454 — Fri, 16 May 2014 10:20:11 GMT

To see the dropdown for Crosslight v2.0, you'll need to open up registry editor. Check the HKLM/Software folder. Make a backup of the registry. If you're running a 64-bit version of Windows, you'll find a Wow6432Node folder. if you happen to find the "Intersoft Solutions" folder as a sibling of the Wow6432Node folder, you'll need to delete the whole folder for the Crosslight 2.0 to properly show up in the Update Manager.
In short, you should not have the Intersoft Solutions folder under HKLM/Software (this only applies to 64-bit Windows), as seen in the attachment. Re-run the LicenseManager from the C:\Program Files (x86)\Intersoft Solutions\Crosslight 2\common\LicenseManager\ISNet.WebUI.LicenseManager.exe, then you should be able to install Crosslight license properly.

I deleted the registry item, but the crosslight 2 option does not appear. Even when I delete the first Crosslight 1.0.5 version.

Any Ideas?

Error when creating a new Crosslight 2 project

nick5454 — Fri, 16 May 2014 09:18:32 GMT

Ok. I'll do the registry thing, but no way will I install that again. I used the new installer for the trial and I never got a menu for intersoft after 10 re-installs. That was a week of sadness...

I feel I got lucky and I don't want to take a chance on issues with dll's again.

Thanks
Nick

Error when creating a new Crosslight 2 project

nicholaslie — Thu, 15 May 2014 23:34:26 GMT

Hi Nick,

You can download the new installer from our Request Trial site. This new installer will allow you to specify the location of the Mobile Studio to be installed. The installer is available through either dashboard or RequestTrial page.

By default, the installer will remove the old ProjectWizard assembly and replace it with the new one. To make sure, open up the Developer Command Prompt for Visual Studio, and run this command: "gacutil /l Intersoft.Crosslight.ProjectWizard" (without quotes). You should find the ProjectWizard updated to version 2.0.0.0, as seenin the attachment.

The VSIX is only used for the installation for Entity Designer Extensions for Visual Studio, the Crosslight ProjectWizard's integration doesn't use VSIX, but instead, a combination of ProjectWizard assembly installed to the Global Assembly Cache and the ProjectTemplates folder in My Documents/Visual Studio 2012/ProjectTemplates/Visual C#/Intersoft Solutions/Mobile/CrosslightApp.zip.

To see the dropdown for Crosslight v2.0, you'll need to open up registry editor. Check the HKLM/Software folder. Make a backup of the registry. If you're running a 64-bit version of Windows, you'll find a Wow6432Node folder. if you happen to find the "Intersoft Solutions" folder as a sibling of the Wow6432Node folder, you'll need to delete the whole folder for the Crosslight 2.0 to properly show up in the Update Manager.

In short, you should not have the Intersoft Solutions folder under HKLM/Software (this only applies to 64-bit Windows), as seen in the attachment. Re-run the LicenseManager from the C:\Program Files (x86)\Intersoft Solutions\Crosslight 2\common\LicenseManager\ISNet.WebUI.LicenseManager.exe, then you should be able to install Crosslight license properly.

Error when creating a new Crosslight 2 project

nick5454 — Thu, 15 May 2014 22:22:40 GMT

So I did this Mr Lie

I was so frustrated and about to give up after going through logs and stuff.

So I installed from the License page only. First I installed the Mobule Full Windows and everything was ok.

I took a snapshot, so I could at least use the first one. THen I downloaded the 2014 Win Full on the same license and it worked just fine and everything is ok.

I took 2 snapshots if you would like them for evaluation. I did notice It still says im no evaulation. Is there a plan to add a license drop down for 2.0 for Windows?

Thanks
Nick

Error when creating a new Crosslight 2 project

nick5454 — Thu, 08 May 2014 14:26:49 GMT

After installing I get this error when creating a crosslight 2.0 project in Visual Studio.

I tried repairing the installation and still get the same result. Where do I find the logs and do I need to additional changes to get the new project to work?